CHP-1200AT3
Ultra-high pressure laser clean dust collector
A high-pressure laser clean dust collector that can maintain a stable suction power for a long time, even under conditions where filter clogging is likely to occur, such as extraction of highly sticky fume generated by laser processing or handling a large amount of dust.
High pressure
AT3 panel
Dust removal function Pulse type
where is delivery date is specified when we delivery model that is compatible with ce standard
For Installation inside inside clean room
CHP-1200AT3
Download manual in pdf
Filter cleaning function [Pulse type]
A proprietary continuous pulse air (compressed air) cleaning function is installed. The interval of the pulse can be adjusted easily.
Ethernet / RS-485
Option feature
All functions that can be operated on the AT3 panel can be operated by a PC with Ethernet or RS-485 communication.
Remote control
Remote cable
(sold separately/model: Using MT-173-8 (3 m) enables remote operation of peripheral equipment.
Motor cable receiving port on main body
- 1.Operation input signal
- 2.Operation pressure signal (DC1-5V)
- 3.Filter clogging signal
- 4.Remote-control operation switching input signal
- 5.Operating signal
- 6.Abnormality signal
- 7.Change of operating level input signal (DC0-5V)
- 8.Gnd
Operation ON/OFF
Change capacity level (air volume)
Primary filter
The zeolite is pre-coated by a proprietary scattering mechanism.
Filter is protected from clogging and a long filter life can be achieved even during the collection of fine dust and viscous fumes caused by laser processing. Teflon filter improve the peeling properties of the zeolite, fumes and dust.
Activated carbon
Deodorizing activated carbon can be installed as an option.
List of application
Extraction of fumes and dust during battery sealing process
Removal of dust and fumes from laser cutting lithium-ion battery electrodes
Removal of dust and fumes from laser cutting polarizing plate
Removal of dust from silicon isolator
Removal of dust when using laser cutting sheet for interior work
Easy primary filter chamber removal mechanism
When you remove the left and right snap locks and open the front cover, it turns into a slope and allow you to pull down the filter chamber easily with the levers on both side of the chamber.
Filter Type
| Model | Primary filter | Secondary filter | Exhaust HEPA filter | Motor cooling filter | Zeolite | |
|---|---|---|---|---|---|---|
| suction | exhaust | |||||
| CHP-1200AT3 | CS-200-500-75P-R x 4 | CHF-3030-20 | HEP-3535-69 | PS/150N(215×115) | CHF-3517-30 | ZEO-2500(2.5kg) |
List Of Specifications
| Model | Output | Voltage | Frequency | Rated current |
|---|---|---|---|---|
| CHP-1200AT3 | 1200W | 200V (single phase) | 50/60Hz | 11.0A |
| Maximum air flow |
Maximum static pressure |
Noise level
*1
|
Suction port (hose) size |
Compressed air consumption volume |
|---|---|---|---|---|
| 5.5㎥/min | 13.5kPa | 54-65dB | φ100 | 24L/1 cycle |
| Compressed air pressure |
To be used with 200-240V |
CE compliant | Panel | Power cable |
|---|---|---|---|---|
| 0.3～0.4Mpa | Standard | – | AT3 | 3m |
| Filter cleaning function | Remote control feature | Suitable for use in clean rooms *2
|
Dust collection volume capability *3
|
Mass |
|---|---|---|---|---|
| Pulse type | Level 10000 | 5.5L | 110.0kg |
| Main body dimensions (D×W×H) |
|---|
| 568×577×1201.5mm |
※1 Measurements obtained in Scale A (dBA) from a randomly selected position at a distance of 1m using a unit with a hose connected to its suction port.
(Pulse noise removed)
※2 Based on factory inspection data.
※3 As a reference, the dust collection capacity is about 70% of the amount that can be withdrawn.
(Pulse noise removed)
※2 Based on factory inspection data.
※3 As a reference, the dust collection capacity is about 70% of the amount that can be withdrawn.
Note:Contents may change without notice.
